Free Shipping on Orders Over $299 | 30-Day Money-Back Guarantee Get a Free Quote

xTool S1: What It Cuts, What It Doesn't, and What I Got Wrong

The Short Answer

If you're on a deadline and need the straight version: yes, the xTool S1 cuts acrylic, 3mm MDF, and most laser-safe foam reliably—but the limits you'll hit first aren't the ones on the spec sheet. They're material batch variance, setup time, and the learning curve on the rotary attachment.

I run rush orders for a small fabrication shop. Over the past two years, I've pushed 40-plus emergency jobs through our S1 units—event signage, prototype enclosures, last-minute retail displays. In March 2024, a client called at 7 a.m. needing 200 acrylic badges for a conference 36 hours out. Straight cuts, 3mm cast acrylic, 20W module. We finished in 11 hours including setup and cleanup. That's not a brag—that's the baseline I now measure every rush quote against.

So when someone asks "can the xTool S1 cut acrylic," my answer is yes, and here's what that actually means in practice.

Why You Should Weigh This Assessment

I'm not a reviewer who runs one test coupon and calls it. I'm the person who gets the call when a client's order arrived wrong and the event is Friday. That changes how you evaluate a machine—you care less about peak specs and more about repeatability under pressure.

Last quarter alone, we processed 47 rush orders. About 60% went through the S1 fleet. Our on-time rate was 95%, and the misses were almost never the laser's fault—they were material sourcing or file prep. That distinction matters when you're deciding what to buy.

One caveat up front: this reflects our shop's experience through January 2025. Firmware updates, module revisions, and accessory releases can shift these numbers. Verify current specs before you budget.

Material-by-Material Reality Check

Acrylic: Yes, With Caveats

The S1 handles 3mm cast acrylic cleanly on the 20W module—nice polished edge, minimal cleanup. Thicker stock (6mm and up) needs slower passes and better air assist, and you'll start seeing more edge haze. Extruded acrylic behaves differently than cast; it tends to bubble and smell worse. We keep a cast-only rule for client work.

Here's where conventional wisdom missed: everything I'd read said you absolutely need air assist for clean acrylic edges. In practice, on 3mm cast, we got comparable results without it—though it matters more as thickness climbs. That said, I wouldn't skip it on a production run. The consistency is worth the accessory cost.

3mm MDF: The Workhorse

If you're searching "3mm MDF for laser cutting," this is the material the S1 was practically built around. It cuts fast, holds detail well, and the 20W module handles it at speeds that make deadline work feasible. We've run hundreds of sheets through ours.

The trap is batch variance. We didn't have a formal material verification process until a batch of "3mm" MDF arrived at 2.7mm and our press-fit joints wouldn't hold. Cost us a half-day rework on a $2,400 order. Now we caliper every incoming batch before it touches the bed. Sounds paranoid until you've been burned.

Laser-Cuttable Foam: Know Your Type

This is where I made my most expensive mistake. I knew I should've tested the foam sample before promising same-day turnaround. Thought "foam is foam." That was the one time it released chlorine gas and we had to evacuate the shop for two hours.

The lesson: PVC foam is a hard no—it releases chlorine and corrodes everything in the room. EVA foam, polyethylene foam, and most polyurethane foams cut fine. We now keep a laminated reference card taped to the machine with approved and banned foam types. The S1 itself does the job well; the operator is the weak link.

Rotary Attachment: Worth the Learning Curve

The xTool S1 rotary works—but it's not plug-and-play the way the marketing suggests. Getting the chuck aligned and the diameter dialed in takes practice. Our first cylindrical job (a set of 12 tumblers for a corporate gift) took three test blanks and about 90 minutes of setup before we ran a single production piece.

Once you've got the workflow down, it's genuinely useful. We now quote cylindrical work confidently. But if you're buying the rotary for a one-off project, factor in a learning afternoon—or rather, closer to a full day if you're not already comfortable with rotary alignment.

Projects That Actually Make Sense on the S1

When people ask about the best laser cut projects for this machine, they usually mean "what won't embarrass me." Based on what we've shipped without drama: architectural models, custom signage (acrylic and MDF), leather patches, engraved glassware (with the rotary), and prototype enclosures.

The sweet spot is flat stock under 6mm and cylindrical work under 80mm diameter. That covers most small-business product work and a surprising amount of event fabrication.

Where it gets shaky: deep relief carving, high-volume production where every second of cycle time matters, and anything requiring metal thickness beyond light engraving. The S1 marks anodized aluminum and stainless nicely; it doesn't cut structural metal. Anyone promising otherwise is overselling.

When the S1 Isn't the Right Call

I'd rather tell you this than have you learn it on a deadline. If your job is mostly thick acrylic (10mm-plus), heavy metal cutting, or continuous production runs measured in thousands of units, the S1 will frustrate you. That's not a knock on the machine—it's a boundary call.

We keep a CO₂ unit for the thick-stock work. The S1 handles probably 70% of our rush jobs, and the other 30% go to the bigger machine or out to a partner shop. Knowing which bucket a job falls into is the actual skill. The vendor who says "this isn't our strength—here's who does it better" earns trust for everything else.

One last thing: ventilation isn't optional. Per IEC 60825-1 laser safety classification, even Class 1 enclosed systems need proper exhaust planning for production work. We learned that the hard way with the foam incident. Budget for the enclosure and the venting before you budget for the accessories.

If you're running deadline work like we are, the S1 is a reliable tool with real limits. Learn the limits before the client call, not during it.

author-avatar
Jane Smith

I’m Jane Smith, a senior content writer with over 15 years of experience in the packaging and printing industry. I specialize in writing about the latest trends, technologies, and best practices in packaging design, sustainability, and printing techniques. My goal is to help businesses understand complex printing processes and design solutions that enhance both product packaging and brand visibility.

Leave a Reply